Elmonas Diamonds All insights

ELMONAS / TRADE INSIGHTS · DESIGN GUIDE

Specialty cuts for designers: from outline to specification

12 November 2026 · Akshay Mungalpara and Rashesh Vadodariya · 6 min read

The short answer

A style name such as old mine, moval or Dutch marquise is a design direction, not a complete cutting instruction; a specialty cut becomes a specification only when the outline, facet style, dimensions and matching criteria are written down and agreed before cutting.

What this means for a buyer: Brief a specialty cut with a drawing and written dimensions, and agree the acceptance check before cutting starts.

Key takeaways

  • Names describe families of looks; they do not fix dimensions, angles or facet counts.
  • Outline and facet style are separate decisions, and a specialty brief should state both.
  • Fragile points, thin corners and deep clefts need a feasibility review before rough is committed.
  • Matched pairs and layouts are accepted on visual evidence, not on names.

What the common style names actually say

Evidence: Observed trade practice

Four names recur in designer briefs, and each says less than it appears to.

Old mine is an antique-style family: a high crown, a small table, a large open culet and a cushion-ish outline are typical, but proportions vary widely between stones sold under the name. Two old mine cuts can sit far apart in outline and face-up pattern.

Moval describes an elongated outline that blends oval and marquise proportions. It names a silhouette, not a facet arrangement; a moval can carry a brilliant or a step pattern.

Dutch marquise is an angular outline with strong points. The name fixes the silhouette more tightly than moval does, but it still leaves the facet style, the point angles and the width-to-length ratio open.

Step cut is a facet arrangement, not an outline: parallel concentric facets, as in emerald and Asscher cuts. A step pattern can be applied to many outlines, including custom ones, and it rewards clean rough because inclusions stay visible.

Outline and facet style are separate decisions

A useful brief treats the outline and the facet arrangement as two lines, not one. The outline is the silhouette: length, width, the shape of the ends, the curvature of the sides. The facet style is how the surface is divided: brilliant, step, mixed or antique-style. Naming "a step-cut moval" or "an antique-style cushion with an open culet" removes most of the ambiguity that a bare style name leaves behind.

This separation also keeps expectations honest. An antique-style pattern cut to modern precision will not reproduce the slight asymmetry of a genuinely old stone, and a sketch of a historical piece is a starting point, not a target that any rough can reach.

From drawing to feasibility

A specialty brief needs a dimensioned drawing or written measurements: length and width, the critical angles at points and corners, total depth where it matters to the setting, and the quantity. The manufacturer then reviews the request against the rough that is actually available.

Some outlines carry fragile points: sharp marquise tips, deep clefts in heart shapes, thin corners on kites and shields. These areas chip in cutting and in setting, so the review should agree how points are protected, whether a slightly blunted tip is acceptable, and what happens if the rough cannot reach the drawn outline. Feasibility is settled per job, in writing, before cutting starts. Nothing about a style name guarantees that a particular size or proportion is feasible in a particular piece of rough.

Pairs, layouts and matched-set evidence

Designers rarely need one specialty stone; they need pairs, graduated sets or layouts that read as one composition. Matching is judged on the stones laid out together: outline, profile, face-up colour and the way the pattern draws the eye. Agree the acceptance check in advance: measured dimensions against the drawing, plus photographic or video evidence of the full set as it will be used. Names and individual reports are necessary paperwork, but a set is accepted on how it looks together.

Specialty work is also a narrow slice of certified supply. In the historical statistics index draft, specialty cuts of all kinds account for 1,088 of 16,679 eligible certified records, 6.52%. That figure describes one dated listing sample, not demand and not what any buyer does; the planning implication is that a named style in a named size may not be sitting in listed stock, so a brief should treat commissioning as one of the routes to plan for. The index is a historical file sample, not a live availability count.

Commissioning without a public promise

Specialty stones are made to order and confirmed per job. The practical route is a written brief, a feasibility review, an agreed acceptance check and a job-specific quotation. Availability is stated as available to order, confirmed in your quotation, and no public page can promise that a named style in a named size is sitting in stock.

For the cutting and measurement process itself, read custom-cut lab-grown diamonds.

Questions

Is an old mine cut an antique diamond?

No. Old mine describes a cutting style family with a high crown, small table and open culet. A newly cut lab-grown diamond can be made in that style; the name says nothing about the age or origin of the stone.

Can any outline be cut in a step pattern?

Many can, but not all. Step facets suit outlines with clean geometry and reward high-clarity rough, because the open facets show inclusions. Feasibility is confirmed per job against the available rough.

How is a matched pair of specialty cuts checked?

By measuring each stone against the agreed drawing and by reviewing the pair together in photographs or video, since matching is a visual judgement as much as a dimensional one.

Sources

  • Cutting-style names, outline and facet-style behaviour, and feasibility practice: Elmonas workshop practice, documented and reviewed 12 November 2026.

Last reviewed: 12 November 2026

Discuss your requirement with Elmonas. We reply on WhatsApp during Surat business hours (IST).

WhatsApp