ELMONAS / EDUCATION
Do lab-grown diamonds pass a diamond tester?
The short answer
A lab-grown diamond is diamond, so it passes a standard thermal diamond tester as diamond; the honest qualification is that handheld testers screen for material, not origin, and some lab-grown stones produce false readings on electrical testers, so no single handheld result settles what a stone is or where it grew.
What is the short answer?
A lab-grown diamond is diamond: same carbon crystal, same thermal behaviour. On a standard thermal tester it reads as diamond, because that is what it is. Two qualifications keep the answer honest. First, a tester screens for material type, not origin: it cannot tell lab-grown from mined, because both are diamond. Second, no handheld device is infallible. The laboratory guidance from IGI documents false results in both directions, so a surprising reading is a reason to stop and check further, not a verdict.
Thermal testers and the moissanite problem
The oldest and most common handheld testers measure thermal conductivity: how fast the stone moves heat away from the probe. Diamond conducts heat extremely well, and so does moissanite, which is why older thermal-only testers can flag a moissanite as diamond. That false positive is about moissanite, not about lab-grown diamond. A lab-grown diamond reads as diamond on a thermal tester for the straightforward reason that it is diamond, with the same conductivity as a mined stone.
Electrical testers and the conductive exceptions
Newer combination testers add an electrical measurement to separate diamond from moissanite: most diamond is electrically insulating, while moissanite conducts. Here the exception runs the other way. Some lab-grown diamonds, particularly certain HPHT-grown stones with trace boron, conduct electricity and can read as moissanite on an electrical tester even though they are diamond. IGI's guidance on handheld testers documents exactly this failure mode. So the retail shorthand "lab-grown diamonds never test as moissanite" is too strong: it is usually true, not always true.
Screening is not identification
Even a correct tester result answers only one question: is this material diamond. It says nothing about where the diamond grew. Origin screening uses different instruments, typically based on photoluminescence or fluorescence behaviour, and conclusive identification of growth method and any post-growth treatment is laboratory work. The practical hierarchy is: a handheld tester is a quick material screen, a screening device narrows origin, and a grading report from a recognised laboratory is the document of record.
Reports, inscriptions and an intake checklist
For a parcel or a mounted piece, the paper trail does what a probe cannot. A workable intake sequence:
- Read the report number and confirm the girdle inscription matches it.
- Verify the number on the laboratory's own online service and reconcile the stated weight, measurements and shape against the stone.
- Run a thermal test as a material screen; expect diamond to read as diamond.
- Treat any electrical-tester anomaly as unresolved until the report and the stone's identity are both verified: a valid report confirms that a stone was graded, not that the stone in front of you is that stone. Some genuine lab-grown diamonds give anomalous electrical readings, but an anomaly is not automatically the known exception. Refer any unresolved discrepancy to the laboratory before acceptance or payment.
- For unreported stones, buy from a source that commits to laboratory verification on request.
What to do with an inconclusive result
Stop rather than guess. An inconclusive or contradictory result, a thermal pass with an electrical flag, a tester that reads differently on the table and the girdle edge, or any reading that conflicts with a verified report, means the handheld devices have reached their limit. The next step is a recognised laboratory, which can identify material, origin and treatment conclusively. Do not reject or accept a stone, and do not renegotiate a parcel, on the strength of one handheld reading.
Questions
Will a lab-grown diamond pass a basic diamond tester?
Yes, on a thermal tester it reads as diamond because it is diamond. The tester cannot tell lab-grown from mined, and some lab-grown stones give false readings on electrical testers, so a single handheld result is a screen, not proof.
Can a tester tell a lab-grown diamond from a natural one?
No. Both are diamond and behave the same way in a thermal or electrical probe. Origin is determined by laboratory instruments and stated on the grading report and girdle inscription.
What should I do if a tester says my reported stone is moissanite?
Verify two things, not one: the report number with the laboratory, and that the stone in front of you is the stone the report describes, by its weight, measured dimensions and girdle inscription. Certain lab-grown diamonds conduct electricity and can trigger exactly this false reading, so a genuine stone can produce it, but a valid report alone cannot rule out substitution. If anything does not reconcile, treat the reading as unresolved and ask a laboratory to confirm before acceptance or payment.
For the verification side of the checklist, read how to read and verify a lab-grown diamond report, and for what the report fields mean, see grading: IGI vs GIA.
Sources
- IGI, Diamond detection and handheld testers: the institute account behind the tester sections above. Thermal testers cannot separate lab-grown from natural diamond, moissanite can read as diamond on a thermal tester, and certain HPHT-grown or boron-bearing lab-grown diamonds can read as moissanite on an electrical tester.
Last reviewed: 12 November 2026
Discuss your requirement with Elmonas. We reply on WhatsApp during Surat business hours (IST).